Pengaruh Penggunaan Aspal Modifikasi Polimer Ethyl Vinyl Acetat (EVA) Terhadap Campuran Laston Asphalt Concrete Wearing Course (AC-WC)
The Effect Of The Use Of Ethyl Vinyl Acetate (EVA) Modification Polymer On Mixed Asphalt Concrete Wearing Course (AC-WC)
DOI:
https://doi.org/10.33084/mits.v10i2.3500Keywords:
AC – WC, Ethylene Vinyl Acetate, Marshall, stabilitas, MQAbstract
Asphalt concrete (Laston) has a high level of flexibility so that the placement of such a layer directly above the wear layer (AC-WC) make this layer susceptible to damage is too high temperature and heavy traffic loads. In addition to these, as well as the damage is too high viscosity when asphalt mixing with aggregate due to the ineffectiveness of quality control in Asphalt Mixing Plant (AMP) so that the asphalt temperature is not controlled. This study is intended to take advantage of Ethylene Vinyl Acetate (EVA) as a polymer in a mixture of Asphalt Concrete – Wearing Course). Stages of materials testing carried out on three specimen to be used, ex Clereng aggregate, asphalt penetration pertamina 60/70, and modifier type of polymer Ethylene Vinyl Acetate (EVA). The test in laboratory with Marshall Test to acquire properties with a value of EVA modified aphalt content variation of 0% (Variation 1), 1% (Variation 2), 2% (Variation 3), 3% (Variation 4), and 4% (Variation 5). The result of Marshall Test showed that the addition variation 1 to variation 5 of EVA modified asphalt tend to increase Optimum Asphalt Content, stability value, and Marshall Quotient (MQ) value of AC-WC mixture. Generally, Asphalt Concrete-Wearing Course (AC-WC) mixtures with the addition of EVA modified asphalt gives the best result compared to AC-WC mixture without EVA modified asphalt
Downloads
References
Sukirman, S. (2003). Rekayasa Jalan Raya. Malang: UMM Pres.
Departemen Pekerjaan Umum. (1990). SNI M-58-1990 Metode Pengujian Aspal Dengan Alat Marshall.
Direktorat Jenderal Bina Marga. (2012). Spesifikasi Umum 2012.
Yildrim, Y. (2005). Polymer Modified Asphalt Binders. Journal of Construction and Building Materials 21. University of Texas. Texas. USA. PP. 66.
The Asphalt Institute. (1993). Mix Design Methods for Asphalt Concrete and Other Hot-Mix Types, Manual Series No. 2 (MS-2), Asphalt Institute, Lexington USA.
Wahyudi, H. (2002). Evaluasi Sifat Marshall Dan Nilai Struktural Campuran Beton Aspal Yang Menggunakan Bahan Ikat Aspal Pertamina Pen 60/70 Dan Aspal Esso Pen 60/70. Tidak Diterbitkan. Tesis Teknik Sipil, Universitas Diponegoro.
Widjaja, A. (2013). Pemeliharaan Jalan Aspal Dengan Perbaikan Lapis Aus. Jurnal Universitas Negeri Surabaya. 1 (1): 1-7.
Yoder, E.J. and Witczak, M.W. (1975). Principles Of Pavement Design. New York: John Wiley & Sons Inc.
Krebs, Robert D. and Walker, Richard D. (1971). Highway Materials. Mc. Graw: Hill Book Company.
Sengoz, B. and Isikyakar, G. (2008). Analysis of styrene-butadiene-styrene polymer modified bitumen using fluorescent microscopy and conventional test methods. J Hazard Mater 150: 424-432.
Bonemazzi, F. (1996). Transport Research Record No. 1535 Material and construction, Characteristic of polymers and polymer-modified binders. Transport Research Reacord No. 1535 Material and construction, characteristic of asphalt binders. Washington D. C: National Academy Press.
Zoorob, S.E. and Suparma, L.B. (2000). Laboratory Design And Investigation Of The Properties Of Continuously Graded Asphaltic Concrete Containing Recycled Plastics Aggregate Replacement (Plastiphalt). Cement And Concrete Composites. 22 (4): 233-242
Downloads
Published
How to Cite
Issue
Section
License
All rights reserved. This publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording.
